TNC Programming & General Maintenance

Course contents

Introduction to HEIDENHAIN products

Preface to NC Programming

  • Introduction on TNC Controls
  • Visual display unit and operating panel
  • Modes of operation
  • Status Display

Basic Skills

  • File Management
  • Tool Table
  • Datum/Preset table

Path Functions

  • Cartesian Coordinates
  • Polar Coordinates

Cycles

  • Drilling cycles
  • Cycles for Milling Pockets, Studs and Slots
  • Cycle for Machining Hole Patterns
  • SL Cycles
  • Coordinate Transformation Cycles

Programming techniques

  • Program Section Repeat
  • Sub programming
  • Nesting
  • Help, Tips and tricks

Preamble to advanced programming

  • Fundamentals of FK
  • SmarT.NC

Basic Maintenance

  • Hardware Overview
  • Information on HSCI technology
  • Accessories of the TNC Control
  • Principle of operation of the TNC Control
  • Wiring & Electrical Configuration
  • Connector designation and pin layout
  • NC Errors / Help
  • Diagnosis of NC faults
  • Log books and service files

Data Organisation

  • Hard disk & File Management
  • Data storage medium (HDR,SSDR,CFR,USB)
  • NC software Update  Ethernet interface, Network setting/Data back-up
  • Code numbers / MOD functions
  • Machine Parameters

PC software

  • TNC Remo NT
  • TNC Analyzer
  • TNC SCOPE
  • PLC Design NT

PLC Basics

  • PLC Structure & PLC compilation
  • PLC Error messages  PLC Diagnosis through PLC Table, Trace etc.

Fault diagnosis of peripheral units

  • Encoders
  • Hand wheel and touch probe
  • Visual display unit and keyboard
ID: 1485 Number of free places
11.06.2024 - 14.06.2024
20.08.2024 - 23.08.2024
15.10.2024 - 18.10.2024
17.12.2024 - 20.12.2024
Location

HEIDENHAIN OPTICS & ELECTRONICS INDIA PRIVATE LIMITED
Citilights Corporate Centre (Ground Floor)
No 1 Vivekananda Road, Off Spurtank Road,
Chetpet, Chennai 600031

Pricing

Rs. 20,000 + GST 18%

Duration

4 days

TNC Programming & General Maintenance

Introduction to HEIDENHAIN products

Preface to NC Programming

  • Introduction on TNC Controls
  • Visual display unit and operating panel
  • Modes of operation
  • Status Display

Basic Skills

  • File Management
  • Tool Table
  • Datum/Preset table

Path Functions

  • Cartesian Coordinates
  • Polar Coordinates

Cycles

  • Drilling cycles
  • Cycles for Milling Pockets, Studs and Slots
  • Cycle for Machining Hole Patterns
  • SL Cycles
  • Coordinate Transformation Cycles

Programming techniques

  • Program Section Repeat
  • Sub programming
  • Nesting
  • Help, Tips and tricks

Preamble to advanced programming

  • Fundamentals of FK
  • SmarT.NC

Basic Maintenance

  • Hardware Overview
  • Information on HSCI technology
  • Accessories of the TNC Control
  • Principle of operation of the TNC Control
  • Wiring & Electrical Configuration
  • Connector designation and pin layout
  • NC Errors / Help
  • Diagnosis of NC faults
  • Log books and service files

Data Organisation

  • Hard disk & File Management
  • Data storage medium (HDR,SSDR,CFR,USB)
  • NC software Update  Ethernet interface, Network setting/Data back-up
  • Code numbers / MOD functions
  • Machine Parameters

PC software

  • TNC Remo NT
  • TNC Analyzer
  • TNC SCOPE
  • PLC Design NT

PLC Basics

  • PLC Structure & PLC compilation
  • PLC Error messages  PLC Diagnosis through PLC Table, Trace etc.

Fault diagnosis of peripheral units

  • Encoders
  • Hand wheel and touch probe
  • Visual display unit and keyboard
Training TNC June 2024-06-11 2024-06-14

HEIDENHAIN OPTICS & ELECTRONICS INDIA PRIVATE LIMITED
Citilights Corporate Centre (Ground Floor)
No 1 Vivekananda Road, Off Spurtank Road,
Chetpet, Chennai 600031

20000 5
Training TNC Aug 2024-08-20 2024-08-23

HEIDENHAIN OPTICS & ELECTRONICS INDIA PRIVATE LIMITED
Citilights Corporate Centre (Ground Floor)
No 1 Vivekananda Road, Off Spurtank Road,
Chetpet, Chennai 600031

20000 6
Training TNC Oct 2024-10-15 2024-10-18

HEIDENHAIN OPTICS & ELECTRONICS INDIA PRIVATE LIMITED
Citilights Corporate Centre (Ground Floor)
No 1 Vivekananda Road, Off Spurtank Road,
Chetpet, Chennai 600031

20000 6
Training TNC December 2024-12-17 2024-12-20

HEIDENHAIN OPTICS & ELECTRONICS INDIA PRIVATE LIMITED
Citilights Corporate Centre (Ground Floor)
No 1 Vivekananda Road, Off Spurtank Road,
Chetpet, Chennai 600031

20000 6